Spohn 782-G Bedienungsanleitung PDF herunterladen

Spohn Performance, Inc.

494 E Lincoln Ave - Myerstown, PA 17067

1-888-365-6064 www.spohn.net

Part# 782-G | Tubular Front Lower A-Arms

1978-1987 GM G-Body

USE OF THIS PRODUCT IS ACCEPTANCE OF SELLER’S DISCLAIMER OF WARRANTY!

By their very nature, competition components are constantly pushed to their limits. While our components

are designed to withstand intense race conditions, it is impossible to control the quality of installation or

the varying conditions in which they are used. It is for this reason that absolutely no warranty or

guarantee is either written or implied. Neither the seller or the manufacturer will be liable for any loss,

damage, or injury – direct or indirect – arising from the use of or inability to determine the use of any

product. Before using, the user should determine the suitability of the product for its intended use, and

the user shall assume all responsibility in connection therewith. Spohn Performance, Inc. makes no

guarantee as to the legality for any specific class. Spohn Performance, Inc. makes no claims, nor does it

intend its products to be used in street driven vehicles. Spohn Performance, Inc. reserves the right to

make changes in design or add to or improve on their product without incurring any obligation to install

the same on product previously manufactured. The Buyer agrees to indemnify and hold Spohn

Performance, Inc. harmless from any claim, action or demand arising out of or incident to the Buyer’s

installation or use of products purchased from Spohn Performance, Inc.

INSTALLATION INSTRUCTIONS

1. This installation should only be performed by an experienced mechanic. Improper coil

spring removal and installation can result in serious injury. If you are not experienced

in this type of installation we recommend you have the installation performed by a

professional mechanic at a commercial garage and/or alignment shop.

2. Begin by jacking up the front of the vehicle and then place jack stands under the

frame to safely support the vehicle. The front wheels need to be off of the ground.

3. Remove both front wheels.

4. On The Driver's Side Only: Remove the top front shock's mounting nut, bushing and

washer. Remove the two lower shock t-bar mounting bolts and then remove the front

shock through the bottom of the a-arm.

5. Remove the front sway bar end link from the a-arm and the sway bar and discard.

6. Turn the spindle all the way in one direction for easier access to the lower ball joint.

Remove the cotter pin from the castle nut on the lower ball joint. Then loosen the

castle nut, but do NOT completely remove it. Using a hammer, hit the spindle around

the ball joint mounting hole until the ball joint pops loose. You may need to use a

pickle fork.

7. Position a jack under the a-arm in the area of the ball joint. Jack up on the a-arm until

there is no tension on the ball joint.

8. Insert an internal spring compressor through the bottom of the a-arm and up through

the inside of the coil spring. Fully compress the spring using the internal spring

compressor (we recommend using our Part# FCSC1 internal coil spring compressor

that is designed specifically for the G-Body application. It makes the job VERY easy!).

9. Remove the castle nut from the lower ball joint.

10. Place a block of wood underneath the front upper a-arm to support and hold the upper

a-arm, spindle, brakes, etc. up in the car. You can also tie this assembly up, but a

block of wood placed between the frame and the underside of the upper a-arm works

great.

11. Carefully lower the jack you placed underneath the lower a-arm and lower the a-arm

as far as it will come down. Hold onto the spring and remove it when it is free as you

lower the a-arm.

12. While holding onto the a-arm, remove both of the mounting bolts that go through the

a-arm bushings at the frame mounts and then remove the a-arm from the vehicle.

13. Lightly sand and/or wire wheel the insides of the frame mounts where the a-arm

bushings ride. When you have removed all dirt, rust and scale from these mounting

areas apply a liberal amount of grease to these areas of the mounts. See the end of

these instructions for information on what type of grease must be used.

14. Properly identify the left side Spohn Performance front lower a-arm. The sway bar end

link and polyurethane bump stop face the FRONT of the vehicle when installed.

1 2

Spohn Performance, Inc 1

Inhaltsverzeichnis

Seite 1 - Spohn Performance, Inc

Spohn Performance, Inc. 494 E Lincoln Ave - Myerstown, PA 170671-888-365-6064 www.spohn.netPart# 782-G | Tubular Front Lower A-Arms1978-1987 GM G-B

Seite 2

15. Apply a liberal amount of grease to the outside faces of all four bushing ends. See the end of these instructions for information on what type of

Verwandte Modelle: 782-S

Kommentare zu diesen Handbüchern

Keine Kommentare

Spohn 782-G Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Spohn 782-G herunter. Spohn 782-G User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: 782-S

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Spohn 782-G