Spohn Q-GMP-A6467 Bedienungsanleitung PDF herunterladen

Tech Line: (952) 985-5675 Fax (952) 985-5679

21730 Hanover Ave. Lakeville, MN 55044

www.QA1.net

ASSEMBLY INSTRUCTIONS

GM COIL OVER CONVERSIONS

READ INSTRUCTIONS COMPLETELY BEFORE STARTING THIS PROJECT

**SEE WARRANTY AND DISCLAIMER ON LAST PAGE**

JAM NUT

STUD TOP SHOCK

3/8" BOLT/ NYLOCK NUT

(LOWER T-BAR MOUNT)

SPRING SEATSPRING SEAT

WASHER

If there have been any alterations from the factory equipment, weight or ride height , call the QA1

tech line before assembling and/or installing any part of this kit. Failure to do so will void all

warranties and refunds.

Figure 1

• Start your QA1 GM coil over conversion by inspecting your chassis. Look for wore out bushings,

ball joints, ect. If anything looks suspect, replace it before continuing.

• Get started by taking a ride height (RH) measurement on both sides of the car (see figure 1). This

ride height measurement should be taken from the top of the wheel well opening down to the

ground. It is recommended to mark the wheel well opening as a reference point for later

measurements.

• Place the floor jack under one of the A-arms. Jack the car up so that a jack stand can be placed

under the frame. Let the jack down so that the frame sets securely on the stand.

• Remove the wheel and then the stock shock absorber. Remove the sway bar mount.

• Using the jack to support the A-arm assembly, loosen and remove one of the ball joint nuts. Use a

Ball Joint/Tie Rod separator to release the ball joint stud from the spindle. Slowly, CAREFULLY,

let the A-arm assembly down until the spring is free and can be moved.

• Remove the nut clips in the A-Arm that retain the stock shock.

• Next clean out the holes that the mounting bolts will go through. In some cases they may have to

be opened up slightly by drilling with a 3/8 bit or using a rat-tail file.

1 2 3 4

Inhaltsverzeichnis

Seite 1 - ASSEMBLY INSTRUCTIONS

Tech Line: (952) 985-5675 Fax (952) 985-5679 21730 Hanover Ave. Lakeville, MN 55044 www.QA1.net ASSEMBLY INSTRUCTIONS GM COIL OVER CONVERSI

Seite 2 - Shown as assembled

INSTALLATION • Screw the aluminum spring seat jam nut (shoulder up) and the spring seat (shoulder up) down to the last thread, and NO further. Now

Seite 3

Tech Line: (952) 985-5675 Fax (952) 985-5679 21730 Hanover Ave. Lakeville, MN 55044 www.QA1.net •GM COIL OVER CONVERSION VALVING ADJUSTM

Seite 4

WARRANTY / DISCLAIMER QA1 warrants that the products will be free from defects in material and workmanship for one year from date of sale to the orig

Verwandte Modelle: Q-GMP-A6872 | Q-GMP-G | Q-GMP-S |

Kommentare zu diesen Handbüchern

Keine Kommentare

Spohn Q-GMP-A6467 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Spohn Q-GMP-A6467 herunter. Spohn Q-GMP-A6467 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: Q-GMP-A6872 | Q-GMP-G | Q-GMP-S |

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Spohn Q-GMP-A6467